loading

Shenzhen Demeng Toy Co., Ltd. focus on making custom designer toys.

Toy Factory Quality Control: AQL, Inspection Stages

Standard toy factory quality control generally uses AQL 2.5 Major / 4.0 Minor for sampling acceptance. Please note that AQL is a sampling tool, not 100% inspection. Demeng Toy’s practice: incoming materials and in-process goods are sampled per AQL, and every single piece undergoes full inspection before shipment. Only pieces that pass full inspection will be packed. Do not interpret AQL 2.5 as “2.5% defects are allowed”. It determines whether a lot is accepted based on lot size, sample size and Ac/Re values. For any individual unit delivered to the customer, it is either 0% defective or 100% defective.

Four-Stage Inspection: IQC, IPQC, FQC, OQC

IQC — Incoming Quality Control. PVC paste resin, color pastes, paints, pad-printing inks, adhesives and packaging cartons are checked upon arrival. We review supplier batch reports, production dates and shelf lives; sample viscosity, color and adhesion; and send key materials to a third-party lab for heavy metal and phthalate screening. If incoming materials are non-compliant, downstream adjustments cannot fix the issue.

IPQC — In-Process Quality Control. After demolding, vinyl blanks are checked for wall thickness, mold lines, flash and deformation. At spray painting, we verify color match against master samples, overspray, color bleed and paint runs. At pad printing, we check registration and print clarity. At assembly, we inspect gaps, glue squeeze-out, and confirm mushroom pegs are heat-softened and seated properly. IPQC inspections do not wait until finished goods are produced. We sample each workstation on a scheduled basis and stop the line for adjustment immediately once issues are found.

FQC — Finished Goods Quality Control. Inspection is conducted by AQL sampling. We check appearance, function, standing balance and accessory completeness. This stage is for lot acceptance, not 100% inspection.

OQC — Outgoing Quality Control / Pre-Shipment Inspection. Demeng does not apply sampling here. Every single piece is fully inspected. We check surface condition, spray paint, pad printing, assembly, standing stability, accessories, and do a final review before packing. Repairable units go through touch-up, sanding or reassembly. Unrepairable units with structural cracks or severe deformation are destroyed and will never be packed. Only after full inspection do we seal boxes, pack cartons and apply labels. AQL is used for incoming and in-process control; the pre-shipment gate relies on 100% inspection instead of sampling.

How to Read the AQL Table

AQL follows ISO 2859-1, General Inspection Level II. Lot size determines sample size, then we check Ac/Re. Ac stands for acceptance number and Re stands for rejection number. Accept the lot if the number of defects in the sample ≤ Ac; reject the lot if the defect count ≥ Re. AQL 2.5 for Major defects is stricter than AQL 4.0 for Minor defects. Critical defects normally follow zero acceptance criteria. The lot sizes below are for reference only. The client’s QC specification shall prevail in actual execution:

Lot Size

Sample Size

Major 2.5 Ac/Re

Minor 4.0 Ac/Re

501–1,200

80

5 / 6

7 / 8

1,201–3,200

125

7 / 8

10 / 11

3,201–10,000

200

10 / 11

14 / 15

Note: AQL does not mean “2.5% defects are acceptable” — it only says how likely the lot is to be judged accepted under the sampling plan. Small lots mean small samples and a higher risk of misjudgment. So critical safety items can’t rely on AQL and get tested separately: small-parts tension, sharp edges and points, cord length, and heavy-metal migration.

Common Defect Classification

Critical Defects: Small parts detachment, sharp edges or points, overlong cords, structural breakage, heavy metal or phthalate exceedance. Zero tolerance for these defects. If found, the whole lot shall be quarantined, root cause investigated and re-testing performed as required.
Major Defects: Overspray, color bleed, obvious color deviation, pad-print misregistration, crooked eye printing, large assembly gaps, unstable standing, off-center gravity, missing accessories and function failure. These hurt shelf appearance and playability, judged under AQL 2.5 Major.
Minor Defects: Light scratches, visible but non-abrasive mold lines, minor printing defects on packaging, surface dust. Judged under AQL 4.0 Minor. Repair where possible; non-repairable minor defects will not affect safety or core functions.
Reference Shop-Floor Defect Rates (subject to product complexity):
Vinyl blanks: uneven wall thickness, air bubbles and gate burrs at 3%–8%
Spray & pad printing: overspray, color bleed and registration errors at 5%–10%
Assembly: gaps and glue squeeze-out at 2%–5%
After 100% final inspection, outgoing defect rate is controlled below 1%. Complex multi-color designs will have a slightly higher rate. These figures are not formal standards, they indicate which workstations need closer monitoring.

How to Draft a Executable QC Specification

Avoid vague wording like “good quality”. Use measurable criteria. A practical QC specification shall cover at least the items below:

Inspection stages and responsible parties: Scope of IQC, IPQC, FQC, OQC, and sign-off personnel.  

Sampling standard: AQL levels, inspection level, Critical/Major/Minor definition and Ac/Re table.

Key dimensions & weight: Total height, head-to-body ratio, wall thickness range, single-piece weight tolerance and center-of-gravity position.

Color & appearance: Approved color swatches, paint passes, pad-print position, acceptance limits for overspray and color deviation.

Functional tests: Standing test, drop test, cross-hatch adhesion test, alcohol rub test and maximum allowable assembly gap.

Packing verification: Checklist of main figure, accessories, cards and desiccant; tick off each item before box sealing.

Nonconformance handling: Rework procedure, destruction criteria, batch traceability and report template. Change management: Whether material, color or mold changes require re-testing and the authorized approver.


Demeng Toy has specialized in vinyl toys in Shenzhen for 12 years. We have partnered with over 2,000 brands, with OEM MOQ starting at 50 pcs. Incoming materials and in-process products are sampled per AQL. Every unit goes through 100% inspection before packing. Repairable units are reworked; unrepairable units are destroyed.

prev
How to Verify a Toy Supplier in China: 10-Step Checklist
Protecting Your Toy IP When Manufacturing in China
next
recommended for you
Get in touch with us
Just leave your email or phone number in the contact form so we can send you a free quote for our wide range of designs!
ADDRESS
Dongjia International 1315, No.19 Longgang Road, Longgang District, Shenzhen, Guangdong Province, China.
Contact us
wechat
whatsapp
Contact customer service
Contact us
wechat
whatsapp
cancel
Customer service