loading

Shenzhen Demeng Toy Co., Ltd. focus on making custom designer toys.

3D Printing for Toy Prototypes: FDM vs SLA vs SLS

For toy prototyping, 3D printing isn’t “the pricier the better” — it depends on how big your piece is, how fine the detail is, and whether it has to hold a screw. On the shop floor, for figure prototypes under 30 cm, SLA (resin printing) is basically the default: fine surface, light layer lines, paintable, size enough. FDM wins on cost and structural strength, good for big volume checks and functional parts; SLS wins on support-free printing, drop resistance, and fitting hinges directly — but its surface is powdery and its detail loses to SLA. Below we run the numbers on all three processes, then cover when you should skip printing entirely and go straight to a vinyl prototype.

Process Comparison: FDM SLA SLS Toys at a Glance

Item

FDM (Fused Deposition)

SLA (Stereolithography)

SLS (Selective Laser Sintering)

Forming principle

Thermoplastic filament heated and extruded, stacked layer by layer

UV laser cures photosensitive resin, layer by layer

Laser sinters nylon powder, layer by layer

Surface detail

Visible layer lines; fine textures and small text blur; stepped sidewalls

Best detail; layer height down to 0.05 mm; eyes, logos, and fine texture read clearly

Medium detail; powdery grain on the surface; fine spikes lose to SLA

Strength & hand-feel

Weak layer bonding, splits along layers when dropped; hard and light

Brittle-ish; thin walls and slender parts snap, but the surface is hard and sandable

Tough and drop-resistant; takes clips, hinges, and moving structures; nylon-like feel

Size limits

Large build platform; advantages on 20–30 cm+ pieces

Platform usually modest; most stable under 30 cm, larger needs split-and-glue

Medium platform; big pieces can be joined, powder bed supports well

Per-sample cost

Lowest — cheap material, machines everywhere

Medium — resin and cleaning fluid add cost; small parts are acceptable

Highest — powder and machine amortization make single samples pricey

Post-processing

Remove supports, sand layer lines, primer hides some

Wash uncured resin, secondary cure, remove supports, sand

Powder removal, sandblast, sealant impregnation; surface work is labor-heavy

Best for

Big volume checks, structural mockups, surface not required

Figure prototypes under 30 cm, detail verification, paint samples

Functional parts, clips, hinges, drop-test pieces

In one line: pick SLA for detail, SLS for strength, FDM for cost and volume.

Post-processing: A Printed Part Is Only a Half-Finished Piece

SLA can’t be touched straight off the machine. The surface carries uncured resin, so parts go through an isopropyl wash, then a second cure box for UV top-up — otherwise the surface stays tacky and paint adhesion fails later. Support points get snipped and sanded; thin-wall parts chip when de-supported, so it’s nibbler work, bit by bit. After sanding comes primer, a check of layer lines and detail, then hand painting. SLA parts are brittle — a light hand on the snips and the sandpaper. If you want a crisp resin 3d print figure with readable eyes and logos, SLA plus this routine is the only honest path.
FDM gets supports and raft removed; layer lines go down with sandpaper and filler, then primer. Its weak layer bonding means aggressive sanding raises fuzz and delaminates — slender parts especially. Its advantage is cheap and fast: fine for internal review, not for a final showcase sample.
SLS comes out of a solid block of powder bed — powder cleaning and sandblasting leave a grainy surface. To paint it, sealant impregnation comes first, or the paint soaks in and mottles. SLS parts are tough and drop-resistant, great for structural verification, but surface detail loses to SLA: fine eyes and small logos go soft.
Post-processing often takes longer than the print itself. When the shop schedules a prototype, printing is a day or two; sanding, painting, and assembly are the bulk.

When to Skip Printing: Cases Where You Don’t Print at All

3D printing isn’t a mandatory step for every project. In these situations, skipping it is the better deal.
First, go straight to a vinyl prototype. If the character is confirmed for rotocast vinyl, the structure isn’t complex, and the size is in the normal range, you can go directly to a wax sample, iron mold, and pre-production sample. A vinyl prototype uses production tooling and production material — the piece matches mass production, which is worth more than a 3D print’s “looks similar.” Printed parts are resin or nylon: hand-feel, wall thickness, and paint adhesion all differ from vinyl. A client who confirms on a print can still say “this isn’t it” when bulk arrives. Demeng’s practice: for simple-structure vinyl styles, the pre-production sample is shot on the iron mold — we don’t fake confirmation with a print. We broke down that flow in the vinyl prototyping article.
Rotocast vinyl pre-production sample
Second, the piece is too big. Beyond 30–40 cm, an SLA platform won’t fit it, and FDM/SLS joined pieces bring seams and warping that are harder to control. Large pieces usually go CNC foam/wood, hand-carved mockups, or direct fiberglass casting — printing takes the longer way around.
Third, you’re only checking volume and proportion. If the question is just “does this character stand at 20 cm, does the head-to-body ratio read right,” a low-precision FDM white model is enough — no need for SLA. Look at the proportions, then decide whether to refine.
Fourth, simple structure, committed quantity. If the form is simple, colors are few, and the order size is already set, going straight to an iron mold and pre-production sample cuts one step versus print-then-cast — and isn’t necessarily slower.
Fifth, you need real material hand-feel. A print can’t give vinyl’s soft bounce, injection’s solidity, or resin’s density. What the client wants to touch is the final material, not photosensitive resin. In that case, make the pre-production sample; don’t substitute a print.
3D printing is a tool, not the destination of the process. Figure prototypes under 30 cm: SLA is safest. Structural parts and drop tests: SLS. Big volume checks and internal reviews: FDM. But if you’re committed to vinyl and the structure isn’t complex, wax sample → iron mold → pre-production sample gets you closer to mass production than any print.
Finished painted rotocast vinyl art toy
prev
2D to 3D Toy Modeling: Turn Sketches into Sculptures
recommended for you
Get in touch with us
Just leave your email or phone number in the contact form so we can send you a free quote for our wide range of designs!
ADDRESS
Dongjia International 1315, No.19 Longgang Road, Longgang District, Shenzhen, Guangdong Province, China.
Contact us
wechat
whatsapp
Contact customer service
Contact us
wechat
whatsapp
cancel
Customer service